Hear from Our Customers
You stop noticing the dull spots every time you walk through your kitchen. The etching from that spilled wine disappears. Your floors reflect light again instead of absorbing it.
Marble restoration in Union Square saves you 70 to 90 percent compared to ripping everything out and starting over. That’s real money back in your pocket while getting results that look brand new.
Your property value gets protected too. Restored marble can add up to 25% to your home’s value according to the National Association of Realtors. That matters in Union Square where the median home price sits at $660,700 and climbing.
You’re not covering up damage or masking problems. Professional marble polishing and restoration removes scratches, eliminates etching, and brings back the natural gloss your stone had when it was first installed. It’s the difference between looking at tired marble every day and actually enjoying the space you paid for.
We’ve been working in Union Square since 2006. We’ve seen what happens to marble in this neighborhood—the wear from foot traffic, the damage from harsh winters, the etching from acidic cleaners people didn’t know would cause problems.
We’re not new to this. Our technicians have years of training specifically in stone restoration, not general contracting. That matters because marble gets ruined easily by someone who doesn’t know what they’re doing.
Union Square properties demand quality work. You’ve got high-value real estate and spaces that need to look right. We use advanced equipment that polishes gently, removes damage without creating new problems, and seals properly so your marble stays protected after we leave.
First, we assess your marble. Not every surface needs the same approach. Etching requires different treatment than staining. Scratches need specific attention. We look at what’s actually wrong before we start working.
Then we clean everything thoroughly. Dirt and grime come off first so we can see the real condition of the stone underneath. This step matters more than most people realize—you can’t restore what you can’t see clearly.
Next comes the restoration work itself. We use professional-grade equipment to remove scratches, eliminate etching, and resurface damaged areas. This isn’t buffing or polishing with store-bought products. We’re actually removing a thin layer of damaged stone to reveal the undamaged marble below.
After resurfacing, we polish to bring back the natural shine. Different marble types need different polishing approaches. We adjust our technique based on your specific stone.
Finally, we seal. High-quality sealer protects your newly restored marble from future staining and damage. It’s not permanent—nothing is—but it gives you real protection that lasts.
Ready to get started?
You get a complete assessment of your marble’s condition. We identify etching from acidic damage, staining from spills, scratches from foot traffic, and any other issues affecting your stone. In Union Square, we see a lot of damage from harsh cleaning products and the grit that comes with changing seasons—snow, salt, and debris that gets tracked inside.
The restoration itself includes resurfacing to remove damage, polishing to restore shine, and sealing to protect against future problems. We’re removing the dull, damaged layer and bringing back the glossy finish underneath.
Union Square homes and businesses deal with specific challenges. Heavy foot traffic wears marble down faster. Humidity from New York weather affects how stone ages. Hard water leaves deposits that build up over time. We account for all of this when we restore your marble floors, countertops, or other surfaces.
You also get honest communication about what’s realistic. Some damage goes too deep for restoration alone. Most doesn’t. We’ll tell you exactly what we can fix and what we can’t before we start. That’s how this should work.
Professional marble restoration in Union Square typically runs $10 to $25 per square foot depending on the condition of your stone and what needs to be done. Floor restoration usually costs less—around $3 to $8 per square foot. Countertops run $5 to $25 per square foot.
Replacement costs significantly more. You’re paying for demolition, disposal, new material, and installation. Marble itself isn’t cheap, and labor rates in NYC run $70 to $110 per hour. Full replacement can easily cost three to ten times what restoration costs.
Most marble that looks bad can be restored. Unless you’ve got cracks running through the stone or major structural damage, restoration gives you the same visual result as replacement for a fraction of the price. You’re saving real money—often thousands of dollars—while getting your marble back to how it looked originally.
Daily use dulls marble over time. Foot traffic wears down the surface. Dirt and grit act like sandpaper, slowly scratching away the polish. Even regular cleaning can cause problems if you’re using the wrong products.
Acidic cleaners are the biggest culprit for etching. Anything with vinegar, lemon juice, or harsh chemicals eats away at marble’s surface, leaving dull white spots that look uneven. A lot of people don’t realize their “natural” cleaner is destroying their stone.
In Union Square specifically, you’re dealing with extra challenges. Snow and salt get tracked inside during winter. Humidity from New York weather affects how marble ages. Hard water deposits build up and create a film that makes everything look cloudy. All of this adds up over months and years until your marble looks nothing like it did when it was new.
Most residential marble restoration projects take one to three days depending on square footage and damage level. A typical kitchen countertop might take four to six hours. Larger floor areas need more time—figure a full day for every 200 to 300 square feet.
We work in sections when possible so you’re not completely without access to your space. Floors need to dry after sealing, which usually takes 24 to 48 hours before you can walk on them normally. Countertops are faster—often ready to use the same day.
The process does create some dust and noise from our equipment, but we contain it as much as possible. We’re not doing demolition or major construction. This is precision work that restores what’s already there. Most Union Square clients are surprised by how little disruption there actually is compared to what they expected.
Etching can almost always be fixed through professional marble refinishing. We remove the damaged surface layer where the etching occurred and polish the stone underneath back to its original finish. Those dull white spots from acidic spills disappear completely.
Stains are trickier but usually fixable. Surface stains come out during the cleaning and polishing process. Deeper stains that have penetrated the stone need poulticing—a specialized treatment that draws the stain out from inside the marble. We assess how deep the stain goes before we start.
Replacement is only necessary when you’ve got structural damage like major cracks or if the marble has been ground down so many times there’s not enough stone left to work with. That’s rare. Most of the “ruined” marble we see in Union Square is completely restorable. The etching around your sink, the stains on your floor, the dull patches near your entryway—those all get fixed through proper restoration.
Use pH-neutral cleaners only. No vinegar, no lemon-based products, nothing acidic. Those eat away at marble and cause the exact etching problems you just paid to fix. Mild dish soap and water work fine for daily cleaning.
Wipe up spills immediately, especially anything acidic like wine, coffee, or juice. The sealer we apply gives you protection, but it’s not invincible. The faster you clean up spills, the less chance they have to penetrate and stain.
Reseal your marble every one to three years depending on use. High-traffic floors need it more often. Countertops that see daily use should get resealed annually. The sealer protects against staining and makes cleaning easier. It’s simple maintenance that prevents expensive problems down the road.
Use mats or rugs in high-traffic areas and near entryways. In Union Square, you’re tracking in salt, grit, and debris from outside. That stuff scratches marble over time. A good mat catches most of it before it reaches your floors.
Marble is softer than most people think. It scratches easily and etches from acidic contact. Using the wrong equipment or technique creates new damage while you’re trying to fix old damage. We see this constantly—homeowners or inexperienced contractors who made things worse.
Professional restoration equipment polishes at specific speeds with specific pressure. Too aggressive and you create uneven spots or remove too much stone. Not aggressive enough and you don’t actually fix the problem. The equipment itself costs thousands of dollars and requires training to use correctly.
The products matter too. Professional-grade polishing compounds, sealers, and treatments work differently than retail products. They’re formulated for specific stone types and specific problems. Using the wrong product can discolor marble, leave residue, or fail to protect properly.
Experience is the biggest factor. A trained technician knows how different marble types respond to restoration, what problems can be fixed and what can’t, and how to get consistent results across an entire surface. In Union Square’s high-value properties, you can’t afford to have someone learning on your marble. The stone gets ruined very easily by inexperienced work.
Local Resources
Useful Links
Other Services we provide in Union Square
